Quick answer: First confirm the link speed in Settings > Network & internet > Ethernet. If it reads 100 Mbps on a Gigabit port, swap the Ethernet cable for a Cat 6 cable you know works, plug into a different port on the router or switch, and check that the device at the other end supports Gigabit. Then open the adapter in Device Manager and set Speed & Duplex to Auto Negotiation, which Intel names as the correct setting for Gigabit. If it still links at 100 Mbps, update or roll back the network driver and turn off the adapter’s power-saving options.
In this guide
- Why a Gigabit port connects at 100 Mbps
- Fix 1: Check the link speed Windows reports
- Fix 2: Swap the cable
- Fix 3: Try another port on the router or switch
- Fix 4: Set Speed & Duplex to Auto Negotiation
- Fix 5: Update or roll back the adapter driver
- Fix 6: Turn off the adapter’s power-saving features
- Fix 7: Isolate the PC, the adapter and the network
- Fix 8: Network reset as a last resort
- Related guides
Applies to: Windows 11 (and Windows 10, where the same settings exist) on desktops and laptops with a built-in or USB Gigabit Ethernet adapter that connects at 100 Mbps instead of 1 Gbps. If the cable isn’t detected at all, see ipconfig Media disconnected in Windows 11: what it means and how to fix it; if the connection fails outright, start with Ethernet not working: how to fix it on Windows 11.
Why a Gigabit port connects at 100 Mbps
When you plug in a cable, the adapter and the port at the other end agree on a speed both of them, and the cable between them, can handle. If anything in that chain can’t do Gigabit, the pair settles on a slower rate, and 100 Mbps (Fast Ethernet) is the next step down. That’s why the fix is a matter of finding the weak link rather than changing a setting in Windows.
| What you notice | Possible cause | Go to |
|---|---|---|
| 100 Mbps on one cable, 1 Gbps on another | Damaged cable, bad connector or older Cat 5 cable | Fix 2 |
| 100 Mbps on one router or switch port only | Faulty port or a Fast Ethernet port | Fix 3 |
| Speed & Duplex set to a fixed 100 Mbps value | Manual setting instead of auto-negotiation | Fix 4 |
| Started after a Windows or driver update | Adapter driver | Fix 5 |
| Speed changes after sleep or on battery | Power-saving feature in the driver | Fix 6 |
| 100 Mbps everywhere, with any cable | The adapter or the PC itself | Fix 7 |
Fix 1: Check the link speed Windows reports
Before changing anything, check what Windows actually negotiated. The link speed is the rate between the PC and the router or switch, not your internet speed. A slow speed test on a 1 Gbps link points to the internet plan or the router, not the cable.
- Open Settings > Network & internet and select Ethernet, the path Microsoft gives for checking an Ethernet connection’s details.
- Look for the Link speed (Receive/Transmit) line in the properties list. In current Windows 11 builds it should show values such as 1000/1000 (Mbps) or 100/100.
You can also check from PowerShell. As general guidance, the Get-NetAdapter cmdlet lists each adapter with a LinkSpeed column:
Get-NetAdapter | Select-Object Name, InterfaceDescription, Status, LinkSpeed
A value of 100 Mbps on an adapter whose description mentions Gigabit, 2.5GbE or similar confirms the problem. Note the adapter name and description, because you’ll need them in Device Manager later.
Fix 2: Swap the cable
The cable is the first thing to rule out. As general guidance, Gigabit Ethernet over copper uses all four wire pairs in the cable, while 100 Mbps needs only two. A cable with one broken wire, a crushed section or a badly crimped plug can still carry 100 Mbps, which is why the connection works but never reaches Gigabit.
Intel’s Gigabit speed troubleshooting article says a Cat 6 or better cable is required for reliable Gigabit and that Cat 5 cabling may not be enough. To test:
- Unplug the cable at both ends and plug it back in firmly until the latch clicks.
- Replace it with a different cable, ideally one labeled Cat 6 (the rating is printed on the jacket), and check the link speed again.
- If the PC connects through a wall jack, patch panel or long run inside the walls, test with a single cable straight from the PC to the router. Wall wiring and its jacks are part of the chain too.
If the new cable brings the link to 1 Gbps, the old one was the cause. Throw it out rather than keeping it as a spare.
Fix 3: Try another port on the router or switch
Intel’s checklist also asks you to confirm that the device on the far end, whether a router, switch or access point, fully supports Gigabit. As general guidance:
- Move the cable to a different LAN port on the router. A single faulty port can negotiate only 100 Mbps.
- Check the model of any switch, powerline adapter or wall plate between the PC and the router. Older or budget switches and some ISP-supplied routers have 10/100 ports, and the whole path can’t be faster than its slowest port. The spec sheet or the label on the device may say 10/100 or 10/100/1000.
- Look at the port lights. On some switches and routers the light color or a second LED shows the speed, but the meaning varies by model, so check its manual.
- Restart the router or switch, then check the link speed again.
Fix 4: Set Speed & Duplex to Auto Negotiation
If someone set the adapter to a fixed speed, it will stay at that speed whatever the cable can do. Intel’s Ethernet Adapter Limited at 100 Mbps article says to make sure Speed & Duplex is set to Auto Negotiation, which should be the default:
- Right-click Start and select Device Manager.
- Expand Network adapters and double-click your Ethernet adapter (for example a Realtek PCIe GbE or Intel Ethernet Connection entry).
- Open the Advanced tab and select Speed & Duplex (some drivers call it Link Speed & Duplex or Speed) in the property list.
- Set the value to Auto Negotiation (or Auto), not 100 Mbps Full Duplex.
- Select OK. The connection drops for a few seconds while the adapter renegotiates.
Don’t go looking for a fixed 1 Gbps option. Intel notes that the idea that a Gigabit choice should appear in this list is incorrect: Auto Negotiation is the right setting for Gigabit and gives 1.0 Gbps when the rest of the equipment negotiates correctly. If the router or switch has its own port speed setting, leave it on auto as well; a fixed speed on one end and auto on the other can leave the link at a lower speed.
Fix 5: Update or roll back the adapter driver
Intel’s Gigabit troubleshooting article puts the driver first on its checklist, and its 100 Mbps article asks whether hardware or software changed recently. If the slowdown began after an update, roll back; otherwise, update.
- Roll back: in Device Manager, open the adapter’s properties, go to the Driver tab and select Roll Back Driver. If the button isn’t available, no earlier driver is stored.
- Update: Intel advises using the PC maker’s (OEM) drivers for OEM network adapters. Check the support page for your PC or motherboard model first, then the chip maker (Intel or Realtek) if your PC maker has nothing newer.
- Download first: save the driver file before you uninstall anything, in case the connection drops. A USB stick or Wi-Fi gets it onto the PC if Ethernet stops working.
For the general steps, including how to keep Windows Update from swapping the driver back, see How to update drivers in Windows 11 (and when not to).
Fix 6: Turn off the adapter’s power-saving features
Some Ethernet drivers include options that lower the link speed or power down parts of the port to save energy. As general guidance, these can keep a link at 100 Mbps, especially on laptops running on battery or after the PC wakes from sleep. The names vary by driver and not every adapter has all of them, so look on the Advanced tab in Device Manager for entries such as:
- Energy-Efficient Ethernet or Energy Efficient Ethernet
- Green Ethernet
- Gigabit Lite or Power Saving Mode
- Reduce Speed On Power Down or Advanced EEE
Set them to Disabled one at a time and check the link speed after each change, so you know which one mattered. On the Power Management tab, you can also clear Allow the computer to turn off this device to save power as a test. Turning these off uses a little more power, which matters little on a desktop.
Fix 7: Isolate the PC, the adapter and the network
If the link stays at 100 Mbps with a new cable, a new port and the right settings, find out which side is at fault. Intel suggests testing the adapter in another system, on another network or with a different cable rated for 1 Gbps, and testing on a network where another device already runs at 1 Gbps:
- Plug a second computer into the same cable and port. If it links at 1 Gbps, the problem is in your PC.
- Plug your PC into a different router or switch, or directly into another computer, as Intel’s point-to-point test suggests.
- For a USB Ethernet adapter, use a USB 3 port (sometimes marked blue or with SS) straight on the PC. As general guidance, a USB 2.0 port or an unpowered hub can’t carry the full Gigabit rate.
- Check whether the PC’s firmware (UEFI or BIOS) has a setting for the onboard LAN port, and whether the board maker has published a firmware update for it.
Intel’s article also mentions the TCP auto-tuning setting, which some users reported changing to clear a speed problem. As general guidance, this setting affects transfer speed rather than the negotiated link speed, so it’s worth a look only when the link reads 1 Gbps but transfers stay slow. To see the current value and set it back to the Windows default, run these in an elevated Command Prompt:
netsh int tcp show global
netsh int tcp set global autotuninglevel=normal
If only your PC fails with every cable and network, Intel’s advice is to have the adapter replaced once your provider confirms the line is set up for Gigabit. A USB or PCIe Gigabit adapter can be a cheaper option than a repair for a desktop or laptop with a faulty onboard port.
Fix 8: Network reset as a last resort
As general guidance, a network reset removes and reinstalls every network adapter and sets networking components back to their defaults. It’s unlikely to fix a cable or port fault, but it can clear driver settings changed by other software. The steps:
- Save your work, and note any VPN, proxy or Wi-Fi passwords you’ll need again.
- Open Settings > Network & internet > Advanced network settings and select Network reset.
- Select Reset now, confirm, and let the PC restart.
- Reinstall or reconfigure VPN software if needed, then check the link speed again.
The reset steps and their side effects are covered in more detail in Ethernet not working: how to fix it on Windows 11. If Ethernet shows a 169.254 address after the reset, see Ethernet doesn’t have a valid IP configuration: 7 fixes.
If the wired link is fine at 1 Gbps and only wireless devices feel slow, the bottleneck is elsewhere; Slow Wi-Fi in Windows 11: how to speed up your connection covers that case.
Related guides
- Ethernet not working: how to fix it on Windows 11
- ipconfig Media disconnected in Windows 11: what it means and how to fix it
- Ethernet doesn’t have a valid IP configuration: 7 fixes
- How to update drivers in Windows 11 (and when not to)
- Slow Wi-Fi in Windows 11: how to speed up your connection
Leave a Reply