Quick answer: open Settings > System > Display > Advanced display, the path Microsoft’s refresh rate page gives, and pick the higher rate from the refresh rate drop-down (Microsoft labels it Choose a refresh rate; wording may differ slightly between Windows 11 versions). If only 60Hz is listed, Windows may not be getting a faster mode to offer. Intel’s support article points to the connection (an adapter, dock or cable that limits bandwidth) and an outdated graphics driver, and Microsoft notes that some rates work only at a different resolution. Plug the monitor straight into the PC with a different cable, update the graphics driver, then check the list again. Microsoft says rates marked with an asterisk don’t support your current resolution, and choosing one changes the resolution.
In this guide
- Check what Windows offers first
- Match your symptom
- Fix 1: Pick the rate in Advanced display
- Fix 2: Connect directly and try another cable
- Fix 3: Update the graphics driver
- Fix 4: Check the monitor’s specs and firmware
- Fix 5: Set the rate in your graphics software
- Fix 6: Laptops and dynamic refresh rate
- Fix 7: Update BIOS and dock firmware
- If games still feel like 60Hz
- Related guides
Applies to: Windows 11 PCs and laptops with a monitor or built-in screen rated above 60Hz (for example 120Hz, 144Hz or 165Hz) that stays at 60Hz. Microsoft’s refresh rate page also covers Windows 10, so most steps may apply there too. If the screen goes blank after you change the rate, see Monitor no signal first; if it flickers, see Screen flickering in Windows 11.
Check what Windows offers first
The refresh rate is how many times per second the screen redraws its image, so a 60Hz display updates 60 times a second, as Microsoft’s page Change the refresh rate on your monitor in Windows explains. Intel notes that the modes you can select depend on both the computer’s setup and what the monitor supports, which is why a 144Hz monitor may still top out at 60Hz.
- Open Settings and go to System > Display > Advanced display. If you have more than one screen, the page may ask you to pick a display first; choose the one you want to check.
- Look at the Display information panel. Microsoft says it shows the current resolution and refresh rate, and whether the display supports variable refresh rate (VRR).
- Open the refresh rate drop-down (Microsoft’s page names it Choose a refresh rate) and see which rates are listed.
If the higher rate is in the list, select it and you’re done (Fix 1 covers the asterisk case). If 60Hz is the highest rate offered, work through Fixes 2 to 5, since the problem may sit somewhere between the monitor and Windows.
Match your symptom
This table is our map of the fixes below, built from the Microsoft, Intel and NVIDIA pages cited in this guide. It isn’t a list any of them publishes, so read each cause as one possibility.
| What you see | Possible cause | Go to |
|---|---|---|
| Higher rate listed with an asterisk | That rate needs a different resolution | Fix 1 |
| Only 60Hz listed, monitor on an adapter, hub or dock | The adapter or dock limits the mode | Fix 2, Fix 7 |
| Only 60Hz listed, direct connection | Cable bandwidth, port choice or graphics driver | Fix 2, Fix 3 |
| Native resolution missing as well | Driver or monitor data (EDID) not read correctly | Fix 3, Fix 4 |
| Laptop screen changes rate by itself | Dynamic refresh rate or a power setting | Fix 6 |
| Windows shows the high rate but games feel slow | Game or VRR settings, not Windows | If games still feel like 60Hz |
Fix 1: Pick the rate in Advanced display
Microsoft notes that an asterisk next to a rate in the Choose a refresh rate list means that rate doesn’t support your current resolution. Selecting it changes the display resolution so the monitor can reach that rate.
That trade-off may be fine for gaming, but text and images may look less sharp at a lower resolution. If you’d rather keep the full resolution, leave the asterisk rates alone and move on to Fix 2, because the full-resolution mode may be missing for a connection or driver reason.
If Windows asks whether to keep the new setting, confirm it only if the picture looks right. If the screen goes dark and you can’t confirm, Windows may switch back by itself after a short wait.
Fix 2: Connect directly and try another cable
Intel’s support article Unable to Select the Native Resolution and Other Supported Refresh Rate of an External Display lists two connection checks:
- Use a direct connection. Disconnect any adapters, converters or docking stations and plug the monitor straight into the PC, since Intel says these can alter the data the monitor sends about its supported modes (EDID).
- Test another cable. Try a different HDMI or DisplayPort cable. Intel notes that cheaper cables may limit bandwidth, and with it what the display can do.
The port may matter as well. Some monitors may reach their top refresh rate on only one of their inputs, or only over DisplayPort, and older HDMI versions may not carry high refresh rates at high resolutions. The monitor’s manual or spec sheet may list which input supports which mode, so check it rather than assuming every port is equal. On a desktop PC with a separate graphics card, also make sure the cable goes into the card’s outputs rather than the ports on the motherboard; the motherboard ports may use the processor’s graphics, which in some cases offers fewer modes.
Change one thing at a time and recheck Advanced display after each change, so you know which part was holding the rate back.
Fix 3: Update the graphics driver
Intel’s article recommends the latest graphics driver, and the driver from your computer maker where one exists. A missing or generic driver may also hide higher modes: if Device Manager lists only Microsoft Basic Display Adapter under Display adapters, Windows may not be using your graphics card’s own driver at all.
- Find out which graphics hardware you have; how to check what graphics card you have in Windows 11 shows several ways.
- Install the current driver from your PC maker or the graphics card maker. Our guide to updating drivers in Windows 11 explains where to get one and how to roll back if a new driver causes trouble.
- Restart the PC and check the refresh rate list in Advanced display again.
If the problem started right after a driver update, rolling back to the previous driver may be the better test; the same drivers guide covers that.
Fix 4: Check the monitor’s specs and firmware
Intel’s first step is to check the monitor maker’s listing for the resolutions and rates it supports. A model name may come in versions with different maximum rates, and some may reach their top rate only at certain resolutions or through certain inputs, so it’s worth confirming the exact figure for your model.
Intel also suggests installing the latest display INF file (the monitor’s driver file, where the maker offers one) and notes that some displays need a firmware update, which the display maker can explain. Some monitors may also have their own on-screen menu options that affect the input or the maximum rate; the monitor’s manual is the place to check, since names may differ between brands.
Fix 5: Set the rate in your graphics software
Windows Settings may be all you need, but your graphics software may show the same modes in a different way:
- NVIDIA Control Panel: NVIDIA’s help page To select a screen refresh rate says to open Change resolution under Display, select the display if you have more than one, and choose a rate from the Refresh rate list. NVIDIA notes that with VRR turned on for a VRR-capable display, the rate is set automatically to the highest one. Newer NVIDIA drivers may no longer include this panel; see NVIDIA Control Panel not showing, which covers the NVIDIA App that may take its place.
- Intel graphics: Intel’s article suggests updating Intel Graphics Command Center and checking whether the native mode appears in its Display section.
- AMD graphics: AMD’s own software may also show display settings; the exact location may vary between versions, so check AMD’s documentation for your driver.
If a rate doesn’t appear in the graphics software either, the cause may sit in the connection or the monitor rather than in Windows.
Fix 6: Laptops and dynamic refresh rate
On Windows 11, Microsoft describes Dynamic refresh rate (DRR), which raises and lowers the rate automatically to balance smooth motion with battery life. Microsoft says the Dynamic refresh rate toggle is on the same Advanced display page and can only be turned on if the hardware supports it. Microsoft says DRR needs a display with VRR support and a refresh rate of at least 120Hz.
Microsoft also notes that DRR shouldn’t affect games designed for VRR, but it can limit the maximum refresh rate of other games. If a game seems to run at a lower rate after you turn DRR on, Microsoft recommends turning DRR off.
A lower refresh rate uses less power, Microsoft points out, so some laptops may drop to 60Hz on battery. In some cases the laptop maker’s own power or display app may control this; plugging in the charger and checking the rate again is a quick test.
Fix 7: Update BIOS and dock firmware
Intel’s article lists two further updates that may add support for larger display modes:
- BIOS: check with the computer maker for the latest system and video BIOS.
- Thunderbolt dock firmware: if you use a Thunderbolt dock, check with the computer maker for the latest firmware.
Before you update the BIOS: follow the PC maker’s instructions exactly, keep a laptop plugged in, and don’t turn the PC off during the update, since an interrupted BIOS update may leave the PC unable to start.
If games still feel like 60Hz
Microsoft notes that if your display supports VRR, changing the Windows refresh rate may be unnecessary for gaming, because many games use VRR automatically. If Windows already shows the higher rate but a game still feels capped, the game’s own display options may set their own refresh rate or frame limit, and V-Sync or a frame cap may hold it at 60. Checking the game’s video settings and the DRR note in Fix 6 may help.
Related guides
- How to check what graphics card you have in Windows 11
- How to update drivers in Windows 11 (and when not to)
- NVIDIA Control Panel not showing? Why it’s gone and what to use
- Screen flickering in Windows 11: how to fix it
- Monitor no signal: how to fix it
Leave a Reply